JPexamは正確な選択を与えて、君の悩みを減らして、もし早くてHP HP0-207認証をとりたければ、早くてJPexamをショッピングカートに入れましょう。あなたにとても良い指導を確保できて、試験に合格するのを助けって、JPexamからすぐにあなたの通行証をとります。
JPexamのHP0-207問題集はあなたの一発合格を保証できる資料です。問題集の的中率はとても高いですから、この問題集だけで試験に合格することができます。信じられなら利用してみてください。不合格になればJPexamは全額返金のことができますから、絶対損にならないです。利用したらHP0-207問題集の品質がわかるようになるので、まず問題集の無料なサンプルを試しましょう。問題集のdemoが無料で提供されますから、JPexamのサイトをクリックしてダウンロードしてください。
HPのHP0-207認定試験に合格するためにたくさん方法があって、非常に少ないの時間とお金を使いのは最高で、JPexamが対応性の訓練が提供いたします。
試験番号：HP0-207問題集
試験科目：Procurve Adaptive EDGE Fundamentals
最近更新時間：2014-04-18
問題と解答：全120問
100％の返金保証。1年間の無料アップデート。
JPexamの専門家チームが君の需要を満たすために自分の経験と知識を利用してHPのHP0-207認定試験対策模擬テスト問題集が研究しました。模擬テスト問題集と真実の試験問題がよく似ています。一目でわかる最新の出題傾向でわかりやすい解説と充実の補充問題があります。
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.jpexam.com/HP0-207_exam.html
NO.1 On switches that support the Switch Setup screen interface, which parameters can be
configured on the Switch Setup screen? Select TWO.
A.STP bridge priority
B.IP address of the TACACS+ server
C.system name and contact information
D.IP address and subnet mask for each VLAN
E.IP address and subnet mask for the default VLAN
Correct:C E
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.2 You have been asked to configure IGMP on a ProCurve Switch 6200yl at a customer site. What
are the steps for enabling IGMP on the switch?
A.Enter the manager level, then issue the ip igmp command.
B.Enter the global configuration context, then issue the ip igmp command.
C.Enter the VLAN context for each VLAN that will support IGMP, then issue the ip igmp command.
D.Enter the interface configuration context for each port configured with a VLAN, then issue the ip igmp
command.
Correct:C
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.3 While using the CLI to configure a ProCurve switch, you must move from the global
configuration level to the port context configuration level for port a1. Which command do you use?
A.port a1
B.ethernet a1
C.interface a1
D.configure a1
Correct:C
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.4 What are the primary solution categories of the Adaptive EDGE Architecture? Select THREE.
A.mobility
B.security
C.reliability
D.availability
E.upgradeability
F.convergence
G.cost-effectiveness
Correct:A B F
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.5 You must update the software on a customer's ProCurve Switch 5412zl. Which statement
correctly describes the process for this operation? Select TWO.
A.Use TFTP for direct serial transfer of the software.
B.Use FTP for in-band transfer of the software through an IP network.
C.Use TFTP for in-band transfer of the software through an IP network.
D.Transfer the software from your workstation using a direct serial transfer.
E.Instruct the switch to search for any available TFTP server without knowing its IP address.
Correct:C D
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.6 You are installing a ProCurve switch at a customer site and must enable remote management
for network administrators. Which configuration parameter is necessary to ensure that
administrators can manage the switch even if they are on different IP networks?
A.default VLAN
B.default gateway
C.default password
D.default management profile
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.7 How do ProCurve switches, configured with link aggregation (also known as port trunking),
handle broadcast traffic?
A.Broadcast traffic is flooded through all of the ports in the trunk.
B.The switch sends a query and receives permission from potential receivers before flooding.
C.Broadcast traffic is handled in exactly the same way it would be without port trunking configured.
D.Broadcast traffic is flooded through non-trunked ports, but forwarded only through one of the ports in
the trunk.
Correct:D
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.8 A customer is planning a Power over Ethernet deployment for a large call center that will use
VoIP telephones. While planning the wiring closets for the deployment, the customer suggests
using the uplink ports of a ProCurve Switch 2650-PWR to provide power to a ProCurve Switch
2600-8-PWR. Which statement describes a correct response to this suggestion?
A.It is only possible if the second switch is a ProCurve Switch 2626-PWR.
B.It is not possible because the 2600-8-PWR cannot act as a Powered Device.
C.It is only possible if the customer adds a ProCurve 600 EPS/RPS to the first switch.
D.It is not recommended because the second switch will not have adequate power redundancy.
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.9 You are about to configure HP Switch Meshing on four ProCurve switches at a customer site.
All of the ports that will be included in the mesh are configured for membership in customer
VLANs. How will the mesh configuration affect the VLAN configuration?
A.The mesh ports will automatically become a tagged member of all configured VLANs.
B.The mesh ports will not be a member of any VLANs until you manually configure its VLAN assignments.
C.The mesh ports will not be 802.1Q-compliant and will only be able to retain membership in a single
untagged VLAN.
D.The mesh ports will automatically become a member of the default VLAN and must be configured for
other VLAN membership.
Correct:A
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.10 You are configuring a ProCurve Layer 2 switch to obtain time information from an SNTP server
located on a different IP network than the switch. Which configuration steps are necessary on the
switch to enable this functionality?
A.The switch cannot be configured to obtain time information from a server on a different IP network.
B.Define a default gateway for the switch, enable SNTP, use the sntp server command to enter the IP
address of the server.
C.Assign a port on the switch to a VLAN that includes the SNTP server, enable SNTP, configure the
switch for SNTP unicast mode.
D.Configure an IP address on the same IP network as the SNTP server, enable TimeP, configure the
switch for SNTP broadcast mode.
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.11 How is traffic prioritization accomplished with IEEE 802.1p?
A.802.1Q-compliant devices enforce priorities based on VLAN ID.
B.802.1Q-compliant devices set one of 8 values in a 3-bit field in the VLAN tag.
C.802.1Q-compliant devices set one of 64 values in a 6-bit field in the IP datagram header.
D.802.1Q-compliant devices dedicate a portion of available bandwidth to each prioritized conversation.
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.12 While examining the spanning tree configuration on a ProCurve switch, you notice that one of
the ports is in the Blocking state. Which statement describes how this port will function in this
state?
A.The port is completely blocked for all purposes.
B.The switch will not forward user traffic through that port, but will forward telnet traffic.
C.The switch will not forward user traffic through that port, but will forward BPDUs through that port.
D.The switch forwards user traffic through that port, but does not receive user traffic through that port.
Correct:C
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.13 At a customer site, you have configured four ProCurve switches for HP Switch Meshing and
Multiple Spanning Tree Protocol. How will the mesh appear to non-mesh switches in the same
spanning tree domain?
A.as a single device
B.as a set of devices without redundant links
C.as devices that cannot participate in the spanning tree
D.as a set of devices with spanning tree enabled to block redundant links
Correct:A
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.14 You are about to update the software on a ProCurve switch. Which command do you use to view
a list of all software versions stored on the switch?
A.show run
B.show flash
C.show startup
D.show version
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.15 You are assigned to configure ProCurve switches at a customer site for in-band management.
Which are in-band management methods? Select TWO.
A.Telnet
B.SNMP
C.XMODEM
D.serial console
E.menu interface
Correct:A B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.16 You must remotely manage a customer's switch using Telnet. Which configuration/monitoring
interfaces are available? Select TWO.
A.web interface
B.menu interface
C.ProCurve Manager
D.boot monitor interface
E.command line interface
Correct:B E
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.17 What are the key principles of the Adaptive EDGE architecture? Select TWO.
A.Control to the Edge
B.Control to the Desktop
C.Command from the Center
D.Management from Anywhere
E.Security throughout the Network
Correct:A C
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.18 You configured Rapid Spanning Tree Protocol on four ProCurve Switch 5348xl switches at a
customer site. During the configuration, you forgot to configure the switches so that
switch-to-switch links are not defined as edge ports. Which statement describes the consequence
of your oversight?
A.The switches in the spanning tree will elect multiple Root bridges.
B.The switches will reject the spanning tree configuration and block all ports until the configuration is
corrected.
C.The switches will be unable to elect a Root bridge and will not be able to forward traffic until the
configuration is corrected.
D.The switches will require more time to elect the Root bridge and resolve the topology, but the spanning
tree will otherwise function normally.
Correct:D
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.19 You are implementing a fully connected HP Switch Mesh at a customer site. Which statement
describes a valid design guideline for HP Switch Meshing?
A.A switch may be connected to no more than four mesh domains.
B.Up to five Switch 5400zl Series switches can be included in a full mesh.
C.All links in a full mesh must operate at the same speed and use the same media type.
D.When a switch is configured for HP Switch Meshing protocol, all of the ports on that switch must
participate in the mesh.
Correct:B
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
NO.20 While using the CLI to configure a ProCurve switch, you must change context from the manager
level to the global configuration level. Which command do you use?
A.exit
B.write
C.global
D.enable
E.configure
Correct:E
HP HP0-207認定証 HP0-207認証試験 HP0-207練習問題 HP0-207認定試験
JPexamは最新のE20-554問題集と高品質の70-461問題と回答を提供します。JPexamの200-120 VCEテストエンジンとC4060-155試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質のICBB PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。
没有评论:
发表评论